燃?xì)獍l(fā)電機組由于其燃料適應性好，發電效率高，機組運行方式靈活等特點，廣泛應用于天然氣發電，生物沼氣發電，垃圾填埋氣發電等領域。在常見的幾種燃?xì)忸愋椭?，由于不同的燃?xì)猱a(chǎn)生來源和工藝過程，燃?xì)庵袝３０喾N雜質。下面就幾種常見的雜質類型進行簡要的分析。

Gas generator units are widely used in natural gas power generation, biogas power generation, landfill gas power generation and other fields due to their good fuel adaptability, high power generation efficiency, flexible unit operation mode and other characteristics. In several common types of fuel gas, due to different sources and processes of fuel gas, fuel gas often contains a variety of impurities. The following is a brief analysis of several common impurity types.

1、顆粒物

1. Particulate matter

粉塵等固體顆粒物對燃?xì)獍l(fā)電機組的影響，主要在于造成過濾器堵塞、進氣量不足和壓力降低等。在發動機氣缸內部會造成缸壁和活塞磨損，同時也會污染潤滑油，進而造成其他部件如滑動軸承的磨損，影響機組的正常運行。

The impact of solid particles such as dust on gas turbine generator units mainly lies in filter blockage, insufficient air intake and pressure reduction. In the engine cylinder, the cylinder wall and piston will be worn, and at the same time, the lubricating oil will be polluted, which will cause the wear of other components, such as sliding bearings, and affect the normal operation of the unit.

、發動機燃?xì)膺M(jìn)氣閥組自帶的過濾器僅用于保護系統不受顆粒物損壞，不能作為工作負荷過濾器。用戶應在燃?xì)夤苈吩O(shè)置工作負荷過濾器，且過濾器在顆粒直徑大于3μm時，低分離率須達到99.99%或以上。

The filter attached to the engine gas inlet valve group is only used to protect the system from particle damage, and cannot be used as the working load filter. The user shall set a working load filter in the gas pipeline, and the filter shall be set with a particle diameter greater than 3 μ M, the low separation rate must reach 99.99% or above.

2、硫

2. Sulfur

在生物沼氣等燃?xì)庵谐３：辛蚧瘹涞群蚧衔铮绻跉飧變?nèi)燃燒則形成二氧化硫和三氧化硫。由于燃?xì)庵泻兴智胰細馊紵矊a(chǎn)生水分，含硫化合物溶于水形成氫硫酸、亞硫酸和硫酸，這些酸性物質會對發動機金屬部件產生腐蝕。

Fuel gas such as biogas often contains sulfur compounds such as hydrogen sulfide, which will form sulfur dioxide and sulfur trioxide if burned in the cylinder. As the fuel gas contains water and the fuel gas combustion will also produce water, sulfur compounds dissolve in water to form hydrosulfuric acid, sulfite and sulfuric acid, which will corrode the metal parts of the engine.

燃?xì)獍l(fā)電機組對于燃?xì)夂蛄康木唧w要求跟機組型號以及燃?xì)饧淄闈舛鹊榷加嘘P(guān)系，一般來說進入發動機的燃?xì)庵泻蚩偭繎?yīng)低于300mg/Nm3。此外，帶預燃室的機型通常有額外的要求。如果有帶催化劑的尾氣處理設備，還需考慮催化劑對硫含量的要求。

The specific requirements for the sulfur content of the gas in the gas generator set are related to the unit model and the gas methane concentration. Generally, the total sulfur content in the gas entering the engine should be less than 300mg/Nm3. In addition, models with precombustion chambers usually have additional requirements. If there is tail gas treatment equipment with catalyst, the sulfur content requirements of catalyst shall also be considered.

3、油

3. Oil

由于不同的運行溫度和熱化學反應過程，生物質熱解和氣化過程中會產生成百上千種不同類別的焦油。通常，此類碳?xì)浠衔镌诘蜏赜隼鋾r凝結成液態，會堵塞進氣系統、渦輪增壓器葉片和中冷器等。對生物質熱解氣進行預處理后，對其中焦油的露點進行分析是一個行之有效的方法。

Due to different operating temperatures and thermochemical reaction processes, hundreds of different types of tar will be produced during biomass pyrolysis and gasification. Usually, such hydrocarbons will be condensed into liquid when they are cold at low temperature, which will block the intake system, turbocharger blades, intercoolers, etc. It is an effective method to analyze the dew point of tar after pretreatment of biomass pyrolysis gas.

這類雜質對發電機組帶來的危害將逐漸累積，并對機組的運行效果，正常維護間隙甚至使用壽命產生非常深遠的負面影響。因此，通過預處理方式去除或減少燃?xì)庵械碾s質非常重要，且需按照燃?xì)獍l(fā)電機組制造商的技術要求和建議來進行。更多相關內容就來我們網站http://www.ttyule.net.cn進行咨詢！

The harm brought by such impurities to the generator set will gradually accumulate, and have a very far-reaching negative impact on the operating effect, normal maintenance clearance and even service life of the unit. Therefore, it is very important to remove or reduce impurities in the gas by pretreatment, and it should be carried out according to the technical requirements and recommendations of the gas generator set manufacturer. More relevant content will come to our website http://www.ttyule.net.cn Consult!